#Centos 7 xampp install yum update#
#Centos 7 xampp install yum full#

If the group is not set, the default user's group Once the file is open, change the next two lines: Unix user/group of processes mo GET YOUR VPS nano /etc/php-fpm.d/www.conf Next, open the following file /etc/php-fpm.d/For our tutorial, we’ll be using ‘nano’: Once PHP has been installed we can enable PHP-FPM and FastCGI support for Lighttpd by running the following command: yum -y install php-fpm lighttpd-fastcgi To install PHP along with all of its necessary extensions, run the following command: yum -y install php php-mysqlnd php-pdo php-gd php-mbstring Step 4: Installing PHP and PHP-FPM with FastCGI You can type ‘exit’ to exit the interface. We have successfully installed and connected to the MariaDB database server. Server version: 5.5.60-MariaDB MariaDB Server If you logged in successfully, you will get the following output: Welcome to the MariaDB monitor. We can connect to the MariaDB command line with the following command: mysql -u root -p └─1076 /usr/libexec/mysqld -basedir=/usr -datadir=/var/lib/mysql ├─ 776 /bin/sh /usr/bin/mysqld_safe -basedir=/usr Loaded: loaded (/usr/lib/systemd/system/rvice enabled vendor preset: disabled)Īctive: active (running) since Tue 11:44:39 CDT 1h 29min ago If everything is fine you should get the following output: We can then check the status of the service by running the following command: systemctl status rvice Once the installation has been completed, we can start and enable the service with these following commands: systemctl start rvice We can install the MariaDB database server using the following commands: yum -y install mariadb mariadb-server If you need database support with your Lighttpd setup, this step can be very useful. The default document root for Lighttpd is /var/Step 3: Installing MariaDB support for Lighttpd It will load the default Lighttpd web page. Next, you can open your favorite web browser and enter your server’s IP Address. Now, we need to restart the Lighttpd web server and everything should work fine. If you see any network errors in the status, open the /etc/lighttpd/nf configuration file and change the line that says e-ipv6 from enable to disable. └─11445 /usr/sbin/lighttpd -D -f /etc/lighttpd/nf Loaded: loaded (/usr/lib/systemd/system/rvice disabled vendor preset: disabled)Īctive: active (running) since Tue 12:52:11 CDT 2s ago rvice - Lightning Fast Webserver With Light System Requirements.To check the status of the service run the following command: systemctl status lighttpd Once the Lighttpd packages have been installed, we can start and enable the service to automatically start at boot. Once the EPEL repository has been enabled, we can install the Lighttpd web server by running the following command: yum install lighttpd

#Centos 7 xampp install yum update#

Step 2: Install Lighttpdīefore installing Lighttpd we need to enable the EPEL repository on our system and update our software packages once again using the following commands: yum -y install epel-release Once the updates are completed, we can move on to the next step. You can do this by running the following command: sudo yum update It’s easy to do, and it won’t take more than a few minutes. Remember to replace “ IP_ADDRESS” and “ PORT_NUMBER” with your server’s respective IP address and SSH port number.īefore starting with the installation, you will need to update your system packages to their latest versions.

#Centos 7 xampp install yum full#

Full SSH root access or a user with sudo privileges is also required.Ĭonnect to your server via SSH as the root user using the following command: ssh IP_ADDRESS -p PORT_NUMBER.

For the purposes of this tutorial, we will use a Centos 7 VPS.

Step 4: Installing PHP and PHP-FPM with FastCGI.

Step 3: Installing MariaDB support for Lighttpd.